Whirlpool Refrigerator light not working: Causes + Fixes (2024)

Most Common Solution

Whirlpool Refrigerator Light Bulb

Repair Instructions:

Begin troubleshooting the Whirlpool refrigerator light issue by replacing the bulb. Burnt-out bulbs are the most common cause of light failure. Replace the bulb before examining other lighting components, as the bulb is the easiest and most likely culprit.

How to Replace Whirlpool Refrigerator Light Bulb:

1. Safety Precautions:

   • Start by unplugging the Whirlpool refrigerator from the power source for your safety.

2. Locate the Light Bulb:

   • Identify the location of the light bulb inside the Whirlpool refrigerator, typically near the top and often beneath a protective cover or lens.

3. Gather Necessary Tools:

   • Ensure you have the required tools, which may include a screwdriver and a replacement light bulb compatible with your Whirlpool refrigerator model.

4. Remove the Protective Cover or Lens:

   • If applicable, remove the protective cover or lens that shields the light bulb. Use the screwdriver to carefully take it off.

5. Unscrew the Old Light Bulb:

   • Carefully unscrew the old light bulb counterclockwise from its socket. Some may be a twist-and-pull design, so be cautious not to break the bulb.

6. Prepare the New Light Bulb:

   • Unpack the replacement light bulb, ensuring it's the correct type and size, and handle it gently to avoid damage.

7. Screw in the New Light Bulb:

   • Carefully screw in the new light bulb clockwise into the socket, ensuring it's snug but not over-tightened. Some may require a twist-and-push motion.

8. Replace the Protective Cover or Lens:

   • Reattach the protective cover or lens that you removed earlier. Secure it with the screwdriver.

9. Plug In and Test:

   • Reconnect the Whirlpool refrigerator to the power source and open the door to test the new light bulb. Ensure it illuminates as expected.

10. Final Check:

    • Inspect the new light bulb to ensure it is properly installed and providing the necessary illumination inside the Whirlpool refrigerator.

View Whirlpool Refrigerator Light Bulb parts

Most Common Solution

Whirlpool Refrigerator Door Switch

Repair Instructions:

Use a multimeter to test the Whirlpool refrigerator door switch for continuity when engaged. The switch should show continuous conductivity with the door closed to power the interior lights. Lack of continuity when the door is shut and the switch triggered indicates a faulty switch needing replacement.

How to Replace Whirlpool Refrigerator Door Switch

1. Safety Precautions:

   • Before beginning any work, unplug the Whirlpool refrigerator to ensure your safety during the replacement process.
   • Clear the area around the door switch and remove any items that might obstruct access to the switch.
2. Locate the Door Switch:
   • Consult the user manual or search online to pinpoint the exact location of the door switch in your specific Whirlpool refrigerator model.
   • Typically, it is positioned near the top of the Whirlpool refrigerator compartment, close to the door hinge.
3. Remove the Old Door Switch:
   • Use a screwdriver to detach the screws securing the old switch in place or gently pry the switch from its position.
   • Disconnect any wires attached to the switch, taking note of their positions for the installation of the new switch.
4. Install the New Door Switch:
   • Connect the wires to the corresponding terminals on the new door switch, ensuring a secure and proper connection.
   • Position the new switch in place and fasten it securely with the appropriate screws or fastenings.
5. Test the New Switch:
   • Plug the Whirlpool refrigerator back into the power source.
   • Test the door switch by opening and closing the Whirlpool refrigerator door to ensure that the light turns on and off as expected.
6. Clean Up:
   • Discard any packaging from the new door switch and return the Whirlpool refrigerator's contents to their original positions.
   • Wipe down the area to remove any dust or debris that may have accumulated during the replacement process.
7. Final Check:
   • Double-check all connections to ensure that the door switch is securely fastened.
   • Verify that the Whirlpool refrigerator light is functioning correctly and that the new door switch has effectively resolved any previous issues.

View Whirlpool Refrigerator Door Switch parts

Most Common Solution

Whirlpool Refrigerator Light Assembly

Repair Instructions:

The Whirlpool refrigerator light assembly may be defective and require replacement. Often manufacturers do not provide the individual light assembly parts separately. In these cases, the entire light assembly unit needs to be replaced. Check manufacturer guidelines to determine if light components can be purchased individually or if the complete assembly is required. When the full unit is needed, replacing just the bulb or cover will not correct the issue.

How to Replace Whirlpool Refrigerator Light Assembly:

1. Safety Precautions:

   • Unplug the Whirlpool refrigerator from the power source to ensure your safety during the replacement process.

2. Locate the Light Assembly:

   • Identify the location of the light assembly inside the Whirlpool refrigerator, often positioned near the top and enclosed by a protective cover or lens.

3. Gather Necessary Tools:

   • Ensure you have the required tools, which may include a screwdriver and a replacement light assembly compatible with your Whirlpool refrigerator model.

4. Remove the Protective Cover or Lens:

   • If applicable, remove the protective cover or lens that shields the light assembly. Use the screwdriver to carefully take it off.

5. Disconnect the Wiring:

   • Carefully disconnect the wiring or connectors attached to the old light assembly. Take note of their positions for reconnection.

6. Unscrew or Unclip the Old Light Assembly:

   • Use the screwdriver to loosen and remove any screws or clips securing the old light assembly. Be gentle to avoid damaging the surrounding components.

7. Remove the Old Light Assembly:

   • Gently slide out or lift the old light assembly from its housing, taking care not to damage any wires or connectors.

8. Prepare the New Light Assembly:

   • Unpack the replacement light assembly and inspect it for any defects. Ensure it is clean and free from any packaging materials.

9. Install the New Light Assembly:

   See Also

   Whirlpool Refrigerator Light Not Working: 6 Ways to Fix ItWhirlpool Refrigerator LED Lights Not Working - Ready To DIYWhy Is My Whirlpool Refrigerator LED Lights Not Working?Whirlpool Refrigerator Light Not Working - Repair Parts
   • Carefully position the new light assembly in the same location as the old one, ensuring it fits securely and snugly.

10. Attach the Wiring:

    • Reconnect the wiring or connectors to the new light assembly, following the same configuration as the old one.

11. Screw or Clip in the New Light Assembly:

    • Secure the new light assembly by reattaching any screws or clips you removed earlier. Ensure the assembly is firmly fastened in place.

12. Replace the Protective Cover or Lens:

    • Reattach the protective cover or lens that you removed earlier, securing it with the screwdriver.

13. Plug In and Test:

    • Reconnect the Whirlpool refrigerator to the power source and open the door to test the new light assembly. Ensure it illuminates as expected.

14. Final Check:

    • Inspect the new light assembly to ensure it is properly installed and providing the necessary illumination inside the Whirlpool refrigerator.

View Whirlpool Refrigerator Light Assembly parts

Most Common Solution

Whirlpool Refrigerator Light Socket

Repair Instructions:

Use a multimeter to check if the Whirlpool refrigerator light socket is receiving power. Power at the socket means the bulb should illuminate if functional. No power indicates an electrical issue, not a faulty socket. If the socket has power but the bulb still won't light, the socket is defective and requires replacement.

How to Replace Whirlpool Refrigerator Light Socket:

1. Safety Precautions:

   • Start by unplugging the Whirlpool refrigerator from the power source to ensure your safety during the replacement process.

2. Locate the Light Socket:

   • Identify the location of the light socket inside your Whirlpool refrigerator, which is typically near the top and often covered by a light cover or lens.

3. Gather Necessary Tools:

   • Ensure you have the required tools for the job, which may include a screwdriver, pliers, and a replacement light socket compatible with your Whirlpool refrigerator model.

4. Remove the Light Cover:

   • If applicable, remove the light cover or lens that protects the light bulb and socket. Use the screwdriver to do this, taking care not to damage the cover.

5. Disconnect the Wiring:

   • Carefully disconnect the wiring or connectors from the old light socket. Pay attention to the configuration of the wires for reconnection.

6. Unscrew the Old Light Socket:

   • Use the screwdriver to loosen and remove the screws that secure the old light socket in place. Keep these screws for attaching the new socket.

7. Remove the Old Light Socket:

   • Carefully pull out the old light socket from its housing. Be cautious not to damage any wires or connectors during this process.

8. Prepare the New Light Socket:

   • Unpack the replacement light socket and inspect it for any defects. Ensure it is clean and free from any packaging materials.

9. Install the New Light Socket:

   • Carefully position the new light socket in the same location as the old one, ensuring it fits securely and snugly.

10. Screw in the New Light Socket:

    • Secure the new light socket by reattaching the screws you removed earlier. Ensure the socket is firmly fastened in place.

11. Reconnect the Wiring:

    • Reconnect the wiring or connectors to the new light socket, following the same configuration as the old one.

12. Replace the Light Cover:

    • Reattach the light cover or lens that you removed earlier, securing it with the screwdriver.

13. Plug In and Test:

    • Reconnect the Whirlpool refrigerator to the power source and turn it on to test the new light socket. Ensure the light bulb illuminates as expected.

14. Final Check:

    • Inspect the new light socket to ensure it is properly installed and functioning, providing proper illumination inside the Whirlpool refrigerator.

View Whirlpool Refrigerator Light Socket parts

Most Common Solution

Whirlpool Refrigerator Light Switch

Repair Instructions:

Use a multimeter to check the Whirlpool refrigerator light switch for electrical continuity. No continuity when the switch is activated indicates a faulty switch that needs replacement. Proper switch operation will show continuous conductivity through the closed circuit when triggered. Lack of continuity means the switch is not properly closing the circuit to power the light. Switches must exhibit continuity to send voltage that illuminates the light when toggled. Replace any defective light switches that fail the continuity test.

How to Replace Whirlpool Refrigerator Light Switch:

1. Safety Precautions:

   • Start by unplugging the Whirlpool refrigerator from the power source to ensure your safety during the replacement process.

2. Locate the Light Switch:

   • Identify the location of the light switch inside your Whirlpool refrigerator. It is typically situated near the top and is activated when the door is opened.

3. Gather Necessary Tools:

   • Ensure you have the required tools for the job, which may include a screwdriver, pliers, and a replacement light switch compatible with your Whirlpool refrigerator model.

4. Access the Light Switch:

   • Depending on your Whirlpool refrigerator model, you may need to remove shelves or other components to access the light switch.

5. Remove the Old Light Switch:

   • Carefully disconnect the wiring attached to the old light switch. This often involves pulling off connectors or gently unclipping wires.

6. Detach the Switch from its Housing:

   • Use the appropriate tool, typically a screwdriver, to release the old switch from its housing. Be gentle to avoid damaging the surrounding components.

7. Prepare the New Light Switch:

   • Unpack the replacement light switch and inspect it for any defects. Ensure it's clean and free from any packaging materials.

8. Install the New Light Switch:

   • Carefully position the new light switch in the same location as the old one, ensuring it fits securely in the switch housing.

9. Attach the Wiring:

   • Reconnect the wiring or connectors to the new light switch, following the same configuration as the old one.

10. Reassemble Shelves and Components:

    • If you removed any shelves or components to access the light switch, reassemble them in their original positions.

11. Plug In and Test:

    • Reconnect the Whirlpool refrigerator to the power source and open the door to test the new light switch. Ensure the Whirlpool refrigerator's interior light turns on as expected.

12. Final Check:

    • Inspect the new light switch to ensure it is properly installed and functioning, activating the interior light when the door is opened.

View Whirlpool Refrigerator Light Switch parts

Most Common Solution

Whirlpool Refrigerator LED Light

Repair Instructions:

The most common reason for a Whirlpool refrigerator light failure is a burnt out LED bulb. Use a multimeter to check if the LED light's connector is receiving power. Sufficient voltage at the connector means the bulb should light. No power indicates an electrical supply issue. With adequate voltage present but no illumination, the LED bulb is defective and requires replacement.

How to Replace Whirlpool Refrigerator LED Light:

1. Safety Precautions:

   • Start by unplugging the Whirlpool refrigerator from the power source to ensure your safety during the replacement process.

2. Locate the LED Light:

   • Identify the location of the LED light inside your Whirlpool refrigerator. It is usually situated in the fresh food compartment or freezer.

3. Gather Necessary Tools and Replacement Parts:

   • Ensure you have the required tools, such as a screwdriver, and acquire a compatible replacement LED light module.

4. Access the LED Light:

   • Depending on your Whirlpool refrigerator model, you may need to remove a cover or panel to access the LED light.

5. Disconnect the Old LED Light:

   • Carefully disconnect the old LED light module from its wiring or connector. Take note of the wire placement for reconnection.

6. Remove the Old Light Module:

   • Gently remove the old LED light module from its mounting point. Some modules are secured with clips, screws, or adhesive.

7. Prepare the New LED Light:

   • Unpack the replacement LED light module and inspect it for any defects. Ensure it is clean and free from any packaging materials.

8. Install the New LED Light:

   • Carefully position the new LED light module in the same location as the old one, securing it in place as per the original installation method.

9. Attach Wiring or Connector:

   • Reconnect the wiring or connector to the new LED light module, ensuring the wires are correctly attached.

10. Reassemble the Cover or Panel:

    • If you removed a cover or panel to access the LED light, reassemble it in its original position.

11. Plug In and Test:

    • Reconnect the Whirlpool refrigerator to the power source and test the operation of the new LED light. Ensure it illuminates as expected when the Whirlpool refrigerator door is opened.

12. Final Check:

    • Inspect the new LED light module to ensure it is properly installed and functioning, providing adequate illumination inside your Whirlpool refrigerator.

View Whirlpool Refrigerator LED Light parts

Common Solution

Whirlpool Refrigerator Light Board

Repair Instructions:

Start by using a multimeter to check if the Whirlpool refrigerator light board is getting the correct voltage. Proper voltage to the light board means it should be powering the light. If the board receives sufficient voltage but the light still fails, then the board is faulty and requires replacement. Lack of voltage indicates a broader electrical supply issue, not a defective board.

How to Replace Whirlpool Refrigerator Light Board:

1. Safety Precautions:

   • Before you begin, unplug the Whirlpool refrigerator from the power source to ensure your safety during the replacement.

2. Locate the Light Board:

   • Identify the location of the light board within your Whirlpool refrigerator. It is usually found near the top of the Whirlpool refrigerator's interior.

3. Gather Necessary Tools:

   • Ensure you have the required tools for the job, which may include a screwdriver, pliers, and the replacement light board compatible with your Whirlpool refrigerator model.

4. Remove the Cover or Shield:

   • Depending on your Whirlpool refrigerator model, there may be a cover or shield protecting the light board. Use the screwdriver to carefully remove it.

5. Disconnect the Wiring:

   • Carefully disconnect the wiring or connectors from the existing light board. Take note of their positions for reconnection.

6. Unscrew the Light Board:

   • Use the screwdriver to remove the screws securing the old light board in place. Keep these screws for attaching the new light board.

7. Remove the Old Light Board:

   • Gently slide out or lift the old light board from its housing, taking care not to damage any wires or connectors.

8. Prepare the New Light Board:

   • Unpack the replacement light board and inspect it for any defects. Ensure it's clean and free from any packaging materials.

9. Install the New Light Board:

   • Carefully position the new light board in the same location as the old one, ensuring it fits snugly and securely.

10. Screw in the New Light Board:

    • Secure the new light board by reattaching the screws you removed earlier, making sure it's firmly fastened.

11. Reconnect the Wiring:

    • Reconnect the wiring or connectors to the new light board in the same configuration as the old one.

12. Replace the Cover or Shield:

    • Reattach the cover or shield that you removed earlier, securing it with the screwdriver.

13. Plug In and Test:

    • Reconnect the Whirlpool refrigerator to the power source and turn it on to test the new light board. Ensure the lights illuminate as expected.

14. Final Check:

    • Inspect the new light board to verify that it is properly installed and functioning, providing adequate illumination inside the Whirlpool refrigerator.

By following these steps, you can successfully replace the Whirlpool refrigerator light board, ensuring that your Whirlpool refrigerator's interior is well-lit and functioning correctly.

View Whirlpool Refrigerator Light Board parts

Rare Solution

Whirlpool Refrigerator Main Control Board

Repair Instructions:

A defective main control board could potentially cause Whirlpool refrigerator light failure, though unlikely. Visually inspect for any burned or damaged components indicating a short. Use a multimeter to check if the board is supplying voltage to the light circuit. No voltage means the board is not providing power, confirming a defective board needing replacement. Testing the output voltage is key to verifying if the board is faulty before replacing unnecessarily.

How to Replace Whirlpool Refrigerator Main Control Board

1. Safety Measures:

   • Start by unplugging the Whirlpool refrigerator to avoid any electrical mishaps during the replacement process.
   • Remove all items from the Whirlpool refrigerator and clear any obstacles that may impede access to the control board.
2. Locate the Control Board:
   • Refer to the user manual or search online for the precise location of the main control board in your specific Whirlpool refrigerator model.
   • Typically, the control board is positioned behind the control panel or at the back of the Whirlpool refrigerator.
3. Remove the Control Panel:
   • Using an appropriate screwdriver, carefully detach the control panel from the Whirlpool refrigerator's exterior.
   • Ensure to keep track of the screws and store them in a secure place to prevent misplacement.
4. Disconnect Wires and Remove the Old Control Board:
   • Identify the wires connected to the control board and note their positions.
   • Gently disconnect the wires by sliding off the connectors or using pliers, depending on the type of connection.
   • Remove the old main control board from its housing by carefully pulling it out.
5. Install the New Control Board:
   • Place the new control board into the designated slot, ensuring a snug and secure fit.
   • Reconnect the wires to the corresponding terminals by firmly pressing them into place.
6. Replace the Control Panel:
   • Reattach the control panel by aligning it with the appropriate slots and securely tightening the screws.
   • Confirm that the panel is properly secured and tightly in place.
7. Restore Power and Test:
   • Plug the Whirlpool refrigerator back into the power source.
   • Set the Whirlpool refrigerator to the recommended settings and monitor its performance over the next few hours.
   • Ensure that the control board is effectively managing the Whirlpool refrigerator's functions and that it is operating as expected.
8. Clean Up:
   • Dispose of any packaging from the new control board and return the Whirlpool refrigerator's contents to their original positions.
   • Wipe down the area to eliminate any dust or debris that may have accumulated during the replacement process.
9. Final Check:
   • Double-check all connections and ensure that the control panel is securely fastened.
   • Confirm that the Whirlpool refrigerator is functioning smoothly and that the new main control board has resolved any previous issues.

View Whirlpool Refrigerator Main Control Board parts

Rare Solution

Whirlpool Refrigerator Dispenser Control Board

Repair Instructions:

A malfunctioning dispenser control board could potentially cause the dispenser light to fail. Visually inspect the board for any burned spots or damaged components indicating a short. Use a multimeter to check if the board is supplying voltage to the light's connector. No voltage means the board is not sending power. This points to a defective board that requires replacement. Testing the output voltage is crucial to verify if the board is at fault before replacing it unnecessarily.

How to Replace Whirlpool Refrigerator Dispenser Control Board

1. Safety Measures:

   • Begin by unplugging the Whirlpool refrigerator to ensure your safety throughout the replacement process.
   • Remove all items from the dispenser area and clear any obstacles that may hinder access to the control board.
2. Locate the Dispenser Control Board:
   • Refer to the user manual or search online to pinpoint the exact location of the dispenser control board in your specific Whirlpool refrigerator model.
   • Typically, it is positioned behind the touchpad or control panel of the dispenser.
3. Remove the Control Panel:
   • Using a suitable screwdriver, carefully detach the control panel from the Whirlpool refrigerator's exterior.
   • Keep track of the screws and store them in a secure place to prevent misplacement.
4. Disconnect Wires and Remove the Old Control Board:
   • Identify the wires connected to the control board and take note of their positions.
   • Gently detach the wires by sliding off the connectors or using pliers, depending on the type of connection.
   • Remove the old dispenser control board from its housing by carefully pulling it out.
5. Install the New Dispenser Control Board:
   • Insert the new dispenser control board into the designated slot, ensuring a secure fit.
   • Reconnect the wires to the corresponding terminals by firmly pressing them into place.
6. Replace the Control Panel:
   • Reattach the control panel by aligning it with the appropriate slots and securely tightening the screws.
   • Confirm that the panel is properly secured and tightly in place.
7. Restore Power and Test:
   • Plug the Whirlpool refrigerator back into the power source.
   • Test the dispenser to ensure the new control board is functioning correctly and effectively dispensing water or ice.
8. Clean Up:
   • Dispose of any packaging from the new dispenser control board and return the Whirlpool refrigerator's contents to their original positions.
   • Wipe down the area to remove any dust or debris that may have accumulated during the replacement process.
9. Final Check:
   • Double-check all connections and ensure that the control panel is securely fastened.
   • Confirm that the Whirlpool refrigerator dispenser is operating smoothly and that the new dispenser control board has resolved any previous issues.

View Whirlpool Refrigerator Dispenser Control Board parts

Door opened too long

Repair Instructions:

A malfunctioning control board could potentially cause the Whirlpool refrigerator light failure, though unlikely. Visually inspect the board for any burned spots or damaged components indicating a short. Use a multimeter to check if the board is supplying voltage to the light circuit. No voltage means the board is not sending power, confirming a defective board needing replacement.

View Whirlpool Door opened too long parts